Wire Wrapped Hearts, Part Deux: Earrings

Welcome to part two of my wire wrapped hearts tutorial!

In this lesson, I will demonstrate how to use the little hearts we made last time into super cute, ready for spring earrings. And I promise that this addition takes very little time and effort. You already did the hard part. :)

Wire Wrapped Heart Earrings

Materials needed:

Two wire wrapped hearts

A bit of 20g wire

Two fishhook earwires

Two pairs of pliers (round nose and needle nose)

Wire cutters

Let's begin! 

 Gather up your hearts from last time and get out the 20g wire.

 Take the end of the wire and wrap it around the needle nose pliers, just like when we made the curls for the hearts.

Do this again, so that when you get back to the beginning, you should have two coils.

Do this twice more, so that you have a total of four complete coils. These will be made into jump rings.

Take the coils off the pliers and grab the wire cutters. Position the cutter so that the cut you make is in line with the beginning of the first coil. In other words, you are trying to make a little ring, so cut each one as close to the end of the last as possible. (Sorry for the blurry picture. I had a hard time trying to show this step.)

When you cut, it should look like this. Depending on how strong your hands are and how good your wire cutters are, the ring might fall away on its own. That is perfectly fine.

Now you have one jump ring.

Repeat this process three more times, creating the remainder of the jump rings we need.

Now we need to open the jump rings so that we can attach them to the hearts. To do this, grab one side of the ring with a pair of pliers. Pull the ring perpendicular to itself, so that you are not stretching or misshaping the ring in any way. You can do this with your hands or by using the second set of pliers.

Now pick up one of the hearts and feed the jump ring through one of the curls at the top of the heart. Close the ring by squeezing it as shown below, so that the ring lays inside the pliers before you squeeze. The ends of the ring should meet. If they do not, you may have to adjust the ring a bit to make it work. These are handmade jump rings, after all.

Do this again for the other curl. And repeat for the second heart.

Now we need two more jump rings to attach the fishhook ear wires to the hearts. So make those now. They can be any size you like, but I would recommend making them at least as big as the first rings you made, if not even a little larger.

Open one of the jump rings with the pliers. Keeping the ring held with the pliers, pick up one of the hearts and feed both of the attached jump rings through the new one. Do not close the jump ring yet.

Now pick up one of the ear wires and feed it onto the open jump ring. Close the jump ring, making sure that there are no gaps. You don't want the hearts falling off while you wear them!

Repeat this process for the second heart and then you are done!

 And here is the finished product, ready to wear, share, or just simply enjoy!

These earrings will be featured in an upcoming giveaway that Trbtany Designs is co-hosting with East of Eden Jewelry, so keep an eye out for that very soon.

I hope you all have enjoyed crafting with me today. If you try these, post a link on here so I can see all of your awesome work! Thanks!

Keeping it Krafty,

The Everyday Jeweler

Wire Wrapped Hearts Tutorial

Good afternoon, readers! You're in for a treat today. I just spent the better part of the afternoon working on a wonderful little tutorial for you all. I hope it is easy enough to follow. I tried to make sure to take pictures of every step along the way. Well....here goes nothing!
Wire Wrapped HeartsMaterials you will need:20 gauge wire 26 gauge wireWire cuttersRound nose pliersNeedle nose pliers(*Not pictured: tape measure, ruler, etc.)

Start by measuring out about 3 inches of the thicker, 20g wire. Cut with wire cutters.

Now measure out around 6 inches of the thinner, 26g wire. Cut with wire cutters.

Place one of each type of wire together so that they cross at the center. (It doesn't have to be exact. You can adjust it later.)

Bend the 26g wire in half, creating a soft V shape.

 Hold the left wire with the index finger and thumb of your left hand. Use your right hand to begin wrapping the 26g wire around the 20g wire.

 

Keep wrapping as tight as you can. If the wrapping gets to spaced out like this:

Then take the round nose pliers and gently squeeze the coils together, making a more uniform look.

Wrap as far as you can by hand. When you get to the end, you may need to use the pliers to wrap the last little bit. (I always use the pliers here. The wire hurts when it is that short.)

This is what it should look like when you have completed the first half of the wire wrapping.

Now turn the whole thing over in your hands so you can work with the remaining wire.

I can usually hold it still with just my fingers, but you may want to use the pliers again to hold the whole thing still while you wrap the remaining section of wire.

Continue wrapping until all the 26g wire has been used up.Then center the coils as best you can. Then squeeze the ends together so you now have another soft V shape.

Use the pliers to make the end come to more of a point, if you like. You can also leave the tip more rounded. Its all a matter of preference.

Now take the needle nose pliers and grab the exposed ends of the wire. You will want to position the wire over the larger part of the pliers to get a bigger circle when we curl.

Now twist the pliers toward yourself, making the wire curl around the pliers. 

Continue twisting until the end of the curl reaches the  rest of the wire.

Now separate the two "arms", making a V shape once again.

Turn the curls so they face into the center.

Now you can adjust the curls to make them wider, more narrow, etc. Again, a matter of preference. I chose to make the curls a bit bigger.

Be sure to do the same to both curls so they are as symmetrical as possible.

Now measure out about 1/2 inch of the 26 gauge wire. This will be used to close up the heart.

Fold this small section of wire into yet another soft V shape.

Feed it through the middle of the curls, from back to front.

Cross the wires so that the left wire is now on the right and the right wire is now on the left. Be sure to pull tight so you get a nice, clean look when you are finished.

Now feed each wire through to the back and cross over to the opposite side again, making sure to pull tight.

Continue doing this until all the wire is coiled around and the ends are tight against the larger wire. Your finished product should look something like this.

And now you're done!!! :)
On Monday I will expand on this tutorial and show you how to take two of these hearts and make them into a super cute pair of earrings!!!  I hope you've enjoyed my tutorial. Feedback is always welcome. If there's something that is unclear or that you have tips on how to improve, please leave me a comment below. Thanks so much!
Until next week,
The Everyday Jeweler

Short and Sweet

Ok, so today's post is, like the title says...short and to the point.
I've been busy all day with a fanning party happening on facebook. This wonderful lady started a party where people with fan pages get together and share the love by liking each other's pages, thus giving everyone new fans. Nifty, huh? It definitely is, but it is also very time consuming. With that and the addition of a friend stopping by this afternoon, I really haven't done much of anything else today. :(
But I suppose if I get even a few more fans out of it, its been worth it.

Now for the big news. I am planning my first tutorial for either tomorrow or Monday, depending on how quick I can get it together. So keep an eye out for that. Its going to be a simple one, but cut me some slack. Its my first go. :-P

Anyway, thanks for reading! Be sure to check back soon for the tutorial!

With love,

The Everyday Jeweler

Awesome Giveaway from Fashion Momma!!

As I opened my blogroll this afternoon, I noticed quite a few decent giveaways being hosted by fellow bloggers. One in particular happened to really catch my eye...

Fashion Momma

is celebrating 300 readers with a great giveaway.

She is offering to give one lucky reader:

1.)  $25 gift card. Your choice of: Old Navy, New York & Co., or Charlotte Russe.

2.)  2 pairs of solid color tights, your choice

3.)  3 accessories chosen for you by her.

Awesome, right?!

I think so. Be sure to visit this stylish lady and give her some love. You might even get some cool stuff in return! :)

Sharing the love,

The Everyday Jeweler

All Wrapped UP

Happy Tuesday, Everyone!

What's so great about Tuesday, you ask? Well, let me tell you:
1.  The dreaded Monday has come and gone
2.  After today, the week is almost half over.
3.  Tomorrow is hump day. (*giggles*...sorry, had to)
4.  Today was SUPER productive. Well, for me at least.

Speaking of productive, I was a busy little bee today. I managed to finish two pairs of earrings and two wire wrapped pendants. (Only one made it onto Etsy so far, but the day is still young.)
I've really gotten into this wire wrapping thing recently. Its so cool to think that you can take a spool of wire, a pair or two of needle nose and round tip pliers and a stone of your choosing, put them together, and you get this amazing, one of a kind piece of jewelry. I have a feeling that I'll be buying a lot of wire in the coming months. I think next time I make it to Michael's I'm going to pick up some copper colored wire, along with some colored wire as well. Not sure what colors though. Any thoughts?

 Here's the banded amethyst pendant I made today. I think it turned out pretty cute.

Another wire wrapped pendant. This one has a green glass stone in the center. Kind of made a basket type thing surrounding it. Not sure if I like this one yet. Maybe it will grow on me...

Earrings made from opaque stone disks with veins of turquoise. The bead is also turquoise.

Wire wrapped crystal starfish earrings. Not bad for a first try at this type of wrapping.

Well, I think that's it for today. Don't forget to comment and let me know what kinds of wire you think I should use in my upcoming projects!

Thanks for reading,

The Everyday Jeweler